Can I Install a Bathtub Myself? Factors to Consider And Actions
Can I Install a Bathtub Myself? Factors to Consider And Actions
Blog Article
Presented here down the page you can locate lots of really good insight on the subject of How to Install a Bathtub Yourself.
Installing a bathtub isn't exactly rocket science, however it does need solid plumbing, carpentry, as well as often, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably tough job. If the old tub is easily easily accessible, the job can move quickly; if you have to open a wall to remove the old tub and also place the brand-new bath tub, the job is a lot harder. In either situation, the job is within a home handyman's skills, although you will require an assistant to vacate the old bathtub as well as set in the new one. Make sure you have certified on your own for the task as well as are comfortable attempting it. Rather than working with a service provider to take control of a halfway-completed job, it is much better to consider using one prior to you begin. Opportunities are you might need a specialist plumber to make tube links.
This short article will assist you install a brand-new tub in your restroom if you have actually currently bought a brand-new tub as well as do not require to change the setup of your previous supply of water pipes.
Your devices and product checklist need to make up the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you ought to do is separate the water system. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The process of removing the existing faucets can be quite bothersome because of the restricted gain access to that is frequently the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel ready for the continuing to be water that will originate from the pipelines. When the supply pipelines have been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Before going on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the current supply pipes.
If you need to fit a monobloc, then you will need reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washers remain in place in between the faucet and the sink. Protect the faucet in position with the manufacturer offered backnut. When the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical faucet connectors. The former type must be attached to the faucet ends first, tightening just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Bathtub
Using the two wood boards under its feet, position the bath tub in the called for placement. The wood boards are handy in uniformly spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four small points.
The next objective is to ensure that the tub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the tub up until the spirit level reads level.
To install faucets, fit all-time low of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Activate the water as well as inspect all joints and new pipework for leakages as well as tighten them if required. Fill the bathtub as well as likewise inspect the overflow outlet and also the regular electrical outlet for leakages.
Lastly, repair the bath paneling as defined in the maker's instruction manual. Tiling and securing around the bath tub ought to wait until the bath tub has actually been used at the very least when as this will resolve it right into its final position.
Planning for the Setup
Firstly, the sustaining framework supplied with the bath should be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets unit to stop stress on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets making use of 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be suited its last position.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to break an inflexible seal, causing the water to permeate the wall surface in between the bath as well as the tiling, bring about complications with dampness as well as feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, and are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of soaked paper or soft rope. Remember to always fill up the tub with water prior to securing, to permit the activity experienced when the tub is in use. The sealant can split rather very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently available on the market. It is advisable to fit the tiles using water-resistant or water resistant adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen person who reads on A Step-by-Step Guide to Installing a Bathtub, I figured sharing that information was worth the trouble. Appreciated our write-up? Please share it. Let other people locate it. Many thanks for going through it.
Make An Appointment
Report this page